Tuesday, August 25, 2009

E39 Front Woofer Replacement


Friday I was really Jone's-ing for a project, but it was late and I was poor. So I decided to finally tackle the front speakers. I wanted to find out if it was feasible to add 6.5" drivers up front. Why 6.5" drivers you say? Well, because they sound better than 5.25" and furthermore, they were the Infinity coaxial set that I had on my Chevy- so I was driven to make this pair fit.

I took the first step and pulled the door apart per the bmw tips.com instructions- easy enough. With the new, larger driver in hand I sized of the clearance and saw that there was not much to be had. BMW designed these panels very tight. I was going to get rid of the stock enclosure completely to make more room, but then I would lose the resonance of the sealed enclosure and have lots of issues with mounting the new drivers. So I removed the weak ol' 5" woofers and tried to make the 6.5" drivers fit.














Well, no surprise, as seen in the size difference, it wasn't just going to 'slip in.' I was going to grind down the high spots (of which there are many) of the enclosure with a Dremel so the new driver could seat flush. That would have been fine, but then there would be gaping holes to fill for proper sealed resonance, so I tried to think laterally.

I have used heat guns before and it so happened that I have access to a couple at the university, so I swung by there @ about 12:30 am Saturday morning and tried not to set off any alarms. The heat gun did the job. It took about an hour per enclosure, but I slowly MELTED and reformed the plastic, trying to make it as flush as possible. This was no simple task. I was tempted to put it in the oven to make the whole thing more ductile, but I didn't want to pull out a soft, sagging mass of ruined plastic. This wasn't pretty, but it made room for the bigger basket.


















The Infinity sits pretty flush, so I'm happy. But there are still lots of air gaps, so I used lots of weather stripping to seal it off. Luckily, I was able to use the factory wiring w/o a hitch.












All bolted in and ready for action.








I was pretty worried after all this work that the driver was not going to allow the door panel to go back on properly. Since everything was larger and the unit protruded more than the old woofer, I thought I was going to have to modify the door panel also. Luckily though, everything went back together as before (I consider that a freebie :). I think the fact that the tweeter pokes out so much was actually a blessing in that is probably pushes the grill away so the woofer cone and rubber surround isn't slapping the grill during hard hits. As you can see it fits and I can tell you things aren't slapping together while driving :).




Now you KNOW I couldn't add these sweet drivers and just power them with that nasty old factory amp, right? NO WAY! I just spliced in the remaining 2 channels on my 4-channel 1000w (claimed) Profile California 1040 amp.








This system SCREAMS! I enjoyed it in my Chevy, but it just sounds so much better in the 540. I still have the factory amp, mids, and tweets going in tandem with the new system- making 16 working speakers. In reality, I don't know how much good the factory system is doing. I am still going to play around with it and see I can't balance the 2 systems and get some quality out of it, but I am skeptical given the low performance of the factory amp. This was a fun install and it was rewarding to see it work.

Angel Eyes DIY Mod E39


I found a few manufacturers of these LED lamp replacements. They are $150 at best. I am going to make my own- for less than $20. Who wants to bet me I can't?

Here are the preliminary pictures I took tonight to prepare myself for the task.


Old, yellow 10w Halogen angel eye lamps. One is out and shining at you.












I took out my D-cell flashlight and made a comparison. About the same output.






Then I tested it against my 8-LED flashlight. Brighter than the flashlight, but the LEDs are more the color I want.






Then I stuck the flashlight right into the headlight housing in the lamp position to see how it looked. I like it already. Though not properly focused, dim, and only a flashlight, I like the color a ton more. If my project doesn't go well I am just going to have to tape 2 of these flashlights in and pop my hood every time I drive to turn them on and off!





Next step is to get some high output LEDs and make a housing to fit. I think for the prototype I am just going to pull out the halogen and insert an LED (with resistor) for proof of concept. Then a better housing can be fabricated.

Wish me luck!

New Nitrous Nut

This is the result of some inspiration I got from my buddy JimLev on roadfly.com. Take a look.

This is a split nut with an integrated handle. Since only the brass nut on the nitrous line failed I really only needed to replace the brass nut. So I modeled this little gadget and cut it out. Now I don't need a wrench every time I want to fill my bottle.












I used superglue to hold it together, but that didn't last. A quick visit to the machine shop made things more stable.



Friday, July 24, 2009

Third Brake Light Fun

This fun time mod evolved from a discussion I raised on the E39 Roadfly.com forum found here: http://bimmer.roadfly.com/bmw/forums/e39/9312074-3.html

I wanted to customize my third brake light by making and installing a blackout. Joe M suggested an elaborate LED setup. This got me thinking about these scrolling LED belt buckles and name tags you see at disco clubs and Tokyo. So, I researched it out a bit and bought one hoping it would work.



Recipe:
E39 BMW
Common handtools
Rachet set
Scrolling LED License Plate Frame

2 hours working time



The frame I bought is a Flash Frames brand. It was the cheapest and most prolific model on eBay. There is also E-Frames, Roadmaster, and other brands with different features. My model boasts 5 message @120 character storage capacity, wireless remote, and a $20 price tag- shipping included. Got it in the mail yesterday; did the project late tonight.

Let's get started...

Get your package and beautiful 8 month pregnant wife to open it -I love her.



On my model, the LED assembly just pops right out of the frame. Discard frame- it's crap.



Disassemble your car to get to the rear deck per these instructions:
http://www.m5board.com/vbulletin/m5-e39-e60-tips-tricks/92491-e39m5-rear-deck-removal-diy-long-detailed.html
Once that's done (95% of the project), getting the brake light module out is very simple. Just go into the trunk, remove the nut shown here, and slide the module back to unlock it. The module is now free.



Undoing this harness will release the module for working freedom.



I pulled out the lens (just unclipped two clips on the bottom of the module) then the parabolic reflector; but the latter ended up not being necessary.



I like to use this indoor/outdoor automotive trim tape (available at all auto parts stores and Wally World). It holds well but will come off clean when desired. I have used it on many projects, especially those which I want to remain reversible. I put it on the backside of two edges of the LED module where they contact the parabolic reflector.



All put back together.



LED module wired directly to the battery for programming.



I just smashed the leads into the harness for ease and reversibility. They are so tight, they aren't going anywhere. Brown is ground. Black/yellow is 12v + switched. The only downer of this project is that the LCM doesn't at all like the fact that I pulled the filament bulb and replaced it with a 500 ma LED module. It kept cycling on and off trying to establish resistance, so the message would start then restart and so on never getting through all the way. So, reluctantly, I have the filament bulb also in right now. I plan to get a red bulb (since my red lens is gone) and insert it behind the message board in it's normal place to give the needed resistance and backlight the LED module in a cool way. Utility AND functionality!


Wire path.


One cheap video to complete the write-up:



The message is programmed via a wireless IR remote control, so I'll just be changing the message through the back window... Now put your car back together and enjoy!